Monthly Archives: June 2020

Left Wing – First Look

With help from my buddy Charlie, I was able to get the left wing out of the stand and onto the workbench. It’s the first time I’ve had a chance to take a good look at the factory quick-build wing panel since it was unloaded from the shipping container back in February.

Wing jigs are not normally supplied with the QB wings, as their attachment points are (partially) occupied by late-stage structural attachments – especially for the outboard (wingtip) area. Nevertheless, I requested (and received) a set of jigs from TAF USA and was able to make effective use of them.

All-in-all, the wing looks pretty good. That’s a big relief. Wires for taxi and landing lights, pitot tube electrical and eventual 3-in-1 wingtip lights are there. Vinyl tubing for pitot airspeed and AOA sensor are in place as well.

Next, I’ll set up for pressure testing the fuel tanks with a homemade water manometer. The integrity of the factory-assembled fuel tanks must be assured before more time passes. What happens if there’s an issue? That’s a complete unknown. I will keep my fingers crossed and hope for the best. Positive thoughts!

Rudder – Composite Tip and Beacon

Never underestimate the amount of procrastination required to get something done.

As usual, parts preparation takes most of the time. The fiberglass tip, as supplied in the kit, was a bit rough. There were quite a few voids and other imperfections in the layup. The trailing edge was too fat to fit nicely with the skin. Cutting and re-gluing with a bit of glass cloth and West 105 epoxy resolved that. The contour of the tip leading edge needed building up and shaping – requiring several passes. Epoxy takes hours to cure, so each step takes a day. Epoxy filler and wet-sandable primer attends similar time-sinking characteristics. Along the way, test fitting and match drilling of the mounting (rivet) holes was accomplished.

I didn’t really like the way the construction manual prescribed M4 rivnuts for the aluminum doubler that serves as the mounting base for the strobe. My concern is that rivnut installation might crush the fiberglass. I opted instead to make a new part that uses MK1000-06 anchor nuts and is riveted in place with AN426-3 solid flush rivets. Having the patience to eventually arrive at the decision to do this and then actually fabricating the mounting plate demanded all of the procrastination I could muster.

Copious foot-dragging precipitated the decisions about wiring and method of tip attachment. For some reason, I just didn’t want to shorten the (rather stiff) wire bundle of the Aveo Mini Max LED beacon. At the same time, I didn’t want the splice to be at or near the point where the wire exits through the bushing in the rib. A loop seemed the answer. And so it was. Final fitting of the tip to the rudder and pulling of the 3,2 x 8 mm rivets went well. I’d long struggled with the temptation of making the tip removable, à la Pascal Latten, by installing dozens of anchor plates, flush rivets and #4-40 screws, but my steadfast procrastination eventually paid off and the scales tipped in favor of just pulling rivets and being done with it.

Elevator – Counter Balance Skins and Composite Tips

Finishing the elevator was accomplished over a period of about 3 weeks. The composite tips needed repeated sessions of fitting, filling, sanding and priming to achieve a satisfactory appearance. The interface between metal and fiberglass part was dramatically improved from what it would have been, had I left the fiberglass parts untouched.

The fiberglass parts were built up, especially around the leading edge, with Poly-Fiber SuperFil epoxy filler to reduce unsightly gaps. It takes a day for the filler to cure before wet sanding with 400 grit 3M paper, followed by Rust-Oleum wet-sandable automotive (rattle can) primer and the better part of another day for that to dry. Patience is the key

Once I was happy with the fit of the tips, it was time to match drill the parts against the holes in the counter balance skins. That was quickly and easily done by hand with my lithium-powered hand drill and a #30 bit. I’d reviewed numerous discussions about how others attached their tips and decided to simply follow the construction manual, using the ordinary 3,2 x 8 mm domed rivets that were supplied with the kit. Done and done.

The elevator tips took a while to complete, but I didn’t get carried away. All-in-all, the results look rather nice – me thinks.